40W 2ch 0-10V CC Driver EULP40A-2WMC
Summary
EULP40A-2WMC is a 40W AC/DC constant current mode output LED driver featuring the multiple levels selectable by switch. EULP40A-2WMC can be connected to 0-10V main controller to achieve a smooth dimming effect.
Technical Paramaters
|
Model |
EULP40A-2WMC | ||
|
Input |
Efficiency | 85%@120VAC,Full load | |
| Voltage | 120VAC-277VAC | ||
| Frequency Range(Hz) | 60Hz | ||
| Power Factor | 0.9@120VAC,Full load | ||
| THD(full load) | <10%@120VAC, Full load | ||
| AC Current(max) | 0.6Amax@120VAC | ||
| Standby power | <1W | ||
| Inrush Current(max) | Cold start,30A(twidth=22us measured at 50% Ipeak)@120VAC | ||
|
Output |
Current(mA)/Voltage (VDC) Power(W) | 415mA/30-50VDC/20.75W 620mA/30-50VDC/31W
830mA/30-50VDC/41.5W |
Current Selection Table
|
| Ripple Current | 8% | ||
| Channel | 2 | ||
| Current Tolerance | ±5% | ||
| No load output voltage | 60VDC | ||
| Turn on time | <1.5s | ||
| Function | Dimming Type | 0-10V | |
| Dimming Range | 1%-100% Dimming to off | ||
| Protection | Short circuit | Close output，recovers automatically after fault removed | |
| No Load | Power supply will not be damaged under no-load condition | ||
|
Safety & EMC |
Surge | L-N: 2KV | |
| Withstand Voltage | I/P-O/P: 3750VAC/1min/5mA | ||
| Safety Standards | UL | ||
| EMC Eission | Class B | ||
| EMC Immunity | Class B | ||
|
Others |
Working Temp. | -20 ~+50 | |
| Storage Temp., Humidity | -40 ~85 20-90%RH | ||
| tc | 90 | ||
| Material | Metal | ||
| IP Rating | IP20 | ||
| Lifetime | 50,000h@ta: 45 | ||
| Warranty Condition | 5 years | ||
| Switch Cycle | >25,000 times | ||
| Packing(weight) | Net weight: --g±5%/PCS; --PCS/Carton; --kg±5%/Carton; Carton Size: --mm(L*W*H) | ||
| Dimension | 280*30*23mm(L*W*H) | ||
Applications
Dimension(mm)
DALI Wiring
Cautions
1.This product should be installed by qualified personnel.
2.This product is non waterproof, need to avoid sun and rain.In case of outdoor use, please ensure it is mounted in a water proof enclosure.
3.Good heat dissipation conditions extend product life. Please install the product in a well-ventilated environment.
4.Please make sure LED power supply output voltage, current is used to meet the product requirements.
5.Please ensure that adequate sized cable is used from the controller to the LED lights to carry the current. Please also ensure that the cable is secured tightly in the connector.
6.Due to safety concerns, PVC or rubber cord of 0.75-1.5mm² is recommended for input and output terminal(s)(excluding signal terminals). Flat power cord is not suitable.Ensure all wire connections and polarities are correct before applying power to avoid any damages to the LED lights.
7.In case of malfunction, do not repair it yourself.
※ The contents of this manual are updated without prior notice. If the function of the product you are using is inconsistent with the instructions, the function of the product shall prevail.Please contact us if you have any questions .
